569 results found.
Year: 2020, Volume: 20, Number: 4
... inserted in granular quantized values of the compressed signal using the (Dg) and overload (Dov) parts, i.e. D= Dg+ Dov. Since ... the representative levels of the corresponding uniform where c= xmax/ σ is the loading factor of the μ-law quantizer quantizer, defined as: and erf() ...
Terms matched: 2 - Score: 12 - 1,263k
Year: 2020, Volume: 20, Number: 4
... Advances in Electrical and Computer Engineering Volume 20, Number 4, 2020 Multi-objective Environmental-economic Load Dispatch Considering Generator Constraints and Wind Power Using Improved Multi-objective Particle Swarm Optimization Tankut ... employ both functional inertia weight and On the other hand, if the valve point loading effects are functional constriction factor. When selecting the text considered in the fuel ...
Terms matched: 2 - Score: 82 - 1,225k
Year: 2020, Volume: 20, Number: 3
... was first proposed and investigated by Prof. and for load torque step changes at nominal parameters and in Zadeh ... 9. Fig. 7 shows the responses of the loaded DFIM after a no- Variation in the moment ... inertia load start. Fig. 10 shows the simulation responses of the DFIM for an increase in moment of ...
Terms matched: 4 - Score: 44 - 1,978k
Year: 2020, Volume: 20, Number: 3
... experimentally. The bistable system is one of the typical SR models. Its essence Schmitt trigger (ST) is an electronic circuit capable of is a Brownian particle overloaded in a bistable potential producing the SR phenomenon and is very simple to well, accompanied by the periodic motive force and noise implement in practice from an operational ...
Terms matched: 1 - Score: 3 - 2,048k
Year: 2020, Volume: 20, Number: 3
... logic low state. The RTS is designed to emulate either a the primary, but also on its value, the filter inductor current, passive or an active load. Therefore, the output stage of the the input voltage, the ratio of the transformer and the converter is modeled with a passive resistor in parallel with ...
Terms matched: 1 - Score: 10 - 1,807k
Year: 2019, Volume: 19, Number: 4
... without having trained whereas some other methods the continually changing load demand while providing high should be trained with sample ... used in power system related Transmission line apparent power and loaded bus voltage problems [1, 20] as ... values, 5-neurons topology may also output desired results reactive loads that the system is studied and tested for with ...
Terms matched: 4 - Score: 86 - 488k
Year: 2019, Volume: 19, Number: 4
... . The fundamental concepts for energy sources with a common load. The proposed topology, by developing SICs can ... the proposed dual- 100 input converter under different output loads is shown in Fig. 50 8. The ... winding by shorting the primary ï‚· In single-input state (FC-load), VC-OUTVR should winding was 1.5uH. control ...
Terms matched: 4 - Score: 70 - 1,060k
Year: 2019, Volume: 19, Number: 4
... Abstract — A solution strategy is presented using a five- A match for real load at three independent frequencies using section transmission line impedance transformer aiming for stubbed coupling ... alternative can be the application of shunt stub matching three distinct frequencies especially for complex loads technique. which is very difficult to attain. As a further contribution, ...
Terms matched: 2 - Score: 83 - 745k
Year: 2019, Volume: 19, Number: 4
... magnetic component are highly non-linear and can be driven into saturation if design specifications are not optimal, especially (a) Epstein square measurement in severe conditions such as overload, inrush currents, Power Analyzer geomagnetically induced currents (GIC) and other faults [2- 6]. In the above situations, there will be ...
Terms matched: 1 - Score: 3 - 423k
Year: 2019, Volume: 19, Number: 4
... Sided Linear Permanent Magnet Flux Switching Machine: No- Load Operation," ACES Journal, vol. 33 ... , L, mm 100 Figure 3. Three phase no-load flux linkage comparison Slot area, Aslot, mm2 ... to achieve an optimized stator for proposed Thrust-ForceAvg and examine overload capability of machine. Considering manufacturing constraints, minimum ...
Terms matched: 5 - Score: 57 - 798k