4/2022 - 5 |
Design and Implementation of Single Stage SEPIC Integrated Parallel Ripple Cancellation Method for LED LightingMAKKAPATI, S. , RAMALINGAM, S. |
View the paper record and citations in |
Click to see author's profile in SCOPUS, IEEE Xplore, Web of Science |
Download PDF (2,886 KB) | Citation | Downloads: 633 | Views: 1,344 |
Author keywords
capacitors, light emitting diode, power factor correction, switching converter, total harmonic distortion
References keywords
power(21), electronics(16), driver(13), electrolytic(11), single(9), capacitor(9), stage(8), industrial(8), current(8), high(7)
Blue keywords are present in both the references section and the paper title.
About this article
Date of Publication: 2022-11-30
Volume 22, Issue 4, Year 2022, On page(s): 39 - 46
ISSN: 1582-7445, e-ISSN: 1844-7600
Digital Object Identifier: 10.4316/AECE.2022.04005
Web of Science Accession Number: 000920289700005
SCOPUS ID: 85150160610
Abstract
LED drivers when operating from a utility source with a diode bridge rectifier poses a higher output ripple which deserves a large capacitance. But, the higher value of capacitors, normally electrolytic, with lesser lifetime reduces the operating time. This paper proposes a single-ended primary inductor converter (SEPIC) with a front-end diode bridge rectifier integrated with a parallel ripple cancellation circuit (PRC) to eliminate the low frequency ac ripple with film capacitors to enhance the lifetime. The front-end SEPIC act as a power factor correction (PFC) circuit and is to be operated in discontinuous conduction mode (DCM) to attain an inherent PFC when fed from the utility source. A Bi-directional Buck-Boost converter is employed as a PRC circuit to ingest the low frequency ripple component and allow the pure dc to the load. The proposed topology exhibits a higher power factor and lesser output ripple with film capacitors of 10 uF, 22 uF compared to the electrolytic capacitors of a higher rating. Comparison is done based on the simulated results using PSIM and verified with an experimental setup of 30 W. The proposed LED driver topology demonstrates as input current Total Harmonic Distortion (THD) of 6.11, and power factor of 0.996. |
References | | | Cited By «-- Click to see who has cited this paper |
[1] H. Chiu, Y. Lo, J. Chen, S. Cheng, C. Lin and S. Mou, "A high-efficiency dimmable LED driver for low-power lighting applications," in IEEE Transactions on Industrial Electronics, vol. 57, no. 2, pp. 735-743, Feb. 2010. [CrossRef] [Web of Science Times Cited 344] [SCOPUS Times Cited 438] [2] H. Kim, S. Jeon, H. Choi, N. Kim, "High performance BCD Integrated buck-boost converter in an AMOLED display with application of self-triggering frequency modulation," Advances in Electrical and Computer Engineering, vol.18, no.3, pp.119-124, 2018. [CrossRef] [Full Text] [Web of Science Times Cited 3] [SCOPUS Times Cited 4] [3] C. Wu, T. Wu, J. Tsai, Y. Chen and C. Chen, "Multistring LED backlight driving system for LCD panels with color sequential display and area control," in IEEE Transactions on Industrial Electronics, vol. 55, no. 10, pp. 3791-3800, Oct. 2008. [CrossRef] [Web of Science Times Cited 92] [SCOPUS Times Cited 105] [4] J. Huang, et al., "Degradation mechanism decoupling of mid-power white-light LEDs by SPD simulation," in IEEE Transactions on Electron Devices, vol. 63, no. 7, pp. 2807-2814, July 2016. [CrossRef] [Web of Science Times Cited 11] [SCOPUS Times Cited 11] [5] C. Qian, X. J. Fan, J. J. Fan, C. A. Yuan, and G. Q. Zhang, "An accelerated test method of luminous flux depreciation for LED luminaires and lamps," Reliability Engineering & System Safety, vol. 147, pp. 84-92, Mar. 2016. [CrossRef] [Web of Science Times Cited 53] [SCOPUS Times Cited 56] [6] A. Padmasali and S. Kini, "A novel measure to analyse the reliability of LED luminaires," Lighting Research & Technology, vol. 51, no. 7, pp. 1063-1076, Sep. 2018. [CrossRef] [Web of Science Times Cited 6] [SCOPUS Times Cited 7] [7] S. Li, S. -C. Tan, C. K. Lee, E. Waffenschmidt, S. Y. Hui and C. K. Tse, "A survey, classification, and critical review of light-emitting diode drivers," in IEEE Transactions on Power Electronics, vol. 31, no. 2, pp. 1503-1516, Feb. 2016. [CrossRef] [Web of Science Times Cited 177] [SCOPUS Times Cited 213] [8] F. Cacciotto, "Off-line constant current LEDs driver using the HVLED primary controller," IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society, 2010, pp. 2601-2605. [CrossRef] [SCOPUS Times Cited 6] [9] M. Shoyama, T. Kurachi, and T. Ninomiya, "Ripple current analysis of an electrolytic capacitor in power factor correctors," Electronics and Communications in Japan (Part II: Electronics), vol. 79, no. 4, pp. 93-101, 1996. [CrossRef] [Web of Science Times Cited 3] [SCOPUS Times Cited 5] [10] M. W. Ahmad, N. Agarwal, P. N. Kumar and S. Anand, "Low-frequency impedance monitoring and corresponding failure criteria for aluminum electrolytic capacitors," in IEEE Transactions on Industrial Electronics, vol. 64, no. 7, pp. 5657-5666, July 2017. [CrossRef] [Web of Science Times Cited 50] [SCOPUS Times Cited 59] [11] M. R. Amaral and A. J. M. Cardoso, "A simple offline technique for evaluating the condition of aluminum-electrolytic-capacitors," in IEEE Transactions on Industrial Electronics, vol. 56, no. 8, pp. 3230-3237, Aug. 2009. [CrossRef] [Web of Science Times Cited 110] [SCOPUS Times Cited 141] [12] K. Harada, A. Katsuki and M. Fujiwara, "Use of ESR for deterioration diagnosis of electrolytic capacitor," in IEEE Transactions on Power Electronics, vol. 8, no. 4, pp. 355-361, Oct. 1993. [CrossRef] [SCOPUS Times Cited 202] [13] B. White, H. Wang, Y. Liu and X. Liu, "An average current modulation method for single-stage LED drivers with high power factor and zero low-frequency current ripple," in IEEE Journal of Emerging and Selected Topics in Power Electronics, vol. 3, no. 3, pp. 714-731, Sept. 2015. [CrossRef] [Web of Science Times Cited 25] [SCOPUS Times Cited 29] [14] B. Poorali and E. Adib, "Analysis of the Integrated SEPIC-flyback converter as a single-stage single-switch power-factor-correction LED driver," in IEEE Transactions on Industrial Electronics, vol. 63, no. 6, pp. 3562-3570, June 2016. [CrossRef] [Web of Science Times Cited 87] [SCOPUS Times Cited 105] [15] S. Lee and H. Do, "A single-switch AC-DC LED driver based on a boost-flyback PFC converter with lossless snubber," in IEEE Transactions on Power Electronics, vol. 32, no. 2, pp. 1375-1384, Feb. 2017. [CrossRef] [Web of Science Times Cited 66] [SCOPUS Times Cited 86] [16] M. Arias, M. Fernandez Diaz, D. G. Lamar, D. Balocco, A. Aguissa Diallo and J. Sebastian, "High-efficiency asymmetrical half-bridge converter without electrolytic capacitor for low-output-voltage AC-DC LED drivers," IEEE Trans. Power Electron., vol. 28, no. 5, pp. 2539-2550, May 2013. [CrossRef] [Web of Science Times Cited 90] [SCOPUS Times Cited 105] [17] J. Zhang, T. Jiang, and X. Wu, "A high-efficiency quasi-two-stage LED driver with multichannel outputs," IEEE Trans. Ind. Electron, vol. 64, no. 7, pp. 5875-5882, Jul. 2017. [CrossRef] [Web of Science Times Cited 18] [SCOPUS Times Cited 22] [18] G. A. Henao, J. A. Castro, C. L. Trujillo, and E. A. Narvaez, "Design and development of a LED driver prototype with a single-stage PFC and low current harmonic distortion," IEEE Lat. Am. Trans, vol. 15, no. 8, pp. 1368-1375, 2017. [CrossRef] [Web of Science Times Cited 14] [SCOPUS Times Cited 17] [19] P. S. Almeida, D. Camponogara, M. Dalla Costa, H. Braga, and J. M. Alonso, "Matching LED and driver life Spans: A review of different techniques," IEEE Ind. Electron. Mag., vol. 9, no. 2, pp. 36-47, Jun. 2015. [CrossRef] [Web of Science Times Cited 105] [SCOPUS Times Cited 127] [20] L. Gu, X. Ruan, M. Xu, and K. Yao, "Means of eliminating electrolytic capacitor in AC/DC power supplies for LED lightings," IEEE Trans. Power Electron., vol. 24, no. 5, pp. 1399-1408, May 2009. [CrossRef] [Web of Science Times Cited 310] [SCOPUS Times Cited 384] [21] X. Ruan, B. Wang, K. Yao, and S. Wang, "Optimum injected current harmonics to minimize peak-to-average ratio of LED current for electrolytic capacitor-less AC-DC drivers," IEEE Trans. Power Electron, vol. 26, no. 7, pp. 1820-1825, Jul. 2011. [CrossRef] [Web of Science Times Cited 84] [SCOPUS Times Cited 94] [22] S. Wang, X. Ruan, K. Yao, S.-C. Tan, Y. Yang, and Z. Ye, "A flicker-free electrolytic capacitor-less AC-DC LED driver," IEEE Trans. Power Electron, vol. 27, no. 11, pp. 4540-4548, Nov. 2012. [CrossRef] [Web of Science Times Cited 297] [SCOPUS Times Cited 342] [23] T.-L. Chern, L.-H. Liu, S.-H. Yeh, Y.-L. Chern, and D.-M. Tsay, "Single-stage Flyback converter for LED driver with inductor voltage detection power factor correction," in 2010 5th IEEE Conference on Industrial Electronics and Applications, Jun. 2010, pp. 2082-2087. [CrossRef] [SCOPUS Times Cited 6] [24] B. Wang, X. Ruan, K. Yao, and M. Xu, "A method of reducing the peak-to-average ratio of LED current for electrolytic capacitor-less AC-DC drivers," IEEE Trans. Power Electron., vol. 25, no. 3, pp. 592-601, Mar. 2010. [CrossRef] [Web of Science Times Cited 283] [SCOPUS Times Cited 336] [25] C. S. Wong, K. H. Loo, Y. M. Lai, M. H. L. Chow and C. K. Tse, "An alternative approach to LED driver design based on high-voltage driving," in IEEE Transactions on Power Electronics, vol. 31, no. 3, pp. 2465-2475, March 2016. [CrossRef] [Web of Science Times Cited 25] [SCOPUS Times Cited 30] [26] Y. Qiu, L. Wang, H. Wang, Y.-F. Liu, and P. C. Sen, "Bipolar ripple cancellation method to achieve single-stage electrolytic-capacitor-less high-power LED driver," IEEE J. Emerg. Sel. Top. Power Electron., vol. 3, no. 3, pp. 698-713, 2015. [CrossRef] [Web of Science Times Cited 89] [SCOPUS Times Cited 109] [27] D. S. L. Simonetti, J. Sebastian and J. Uceda, "The discontinuous conduction mode Sepic and Cuk power factor preregulators: analysis and design," in IEEE Transactions on Industrial Electronics, vol. 44, no. 5, pp. 630-637, Oct. 1997. [CrossRef] [Web of Science Times Cited 239] [SCOPUS Times Cited 341] [28] Y. Wang, N. Qi, Y. Guan, C. Cecati, and D. Xu, "A single-stage LED driver based on SEPIC and LLC circuits," IEEE Trans. Ind. Electron., vol. 64, no. 7, pp. 5766-5776, Jul. 2017. [CrossRef] [Web of Science Times Cited 47] [SCOPUS Times Cited 67] [29] U. Ramanjaneya Reddy and B. L. Narasimharaju, "Single-stage electrolytic capacitor less non-inverting buck-boost PFC based AC-DC ripple free LED driver," IET Power Electronics, vol. 10, no. 1, pp. 38-46, Jan. 2017. [CrossRef] [Web of Science Times Cited 66] [SCOPUS Times Cited 81] Web of Science® Citations for all references: 2,694 TCR SCOPUS® Citations for all references: 3,528 TCR Web of Science® Average Citations per reference: 90 ACR SCOPUS® Average Citations per reference: 118 ACR TCR = Total Citations for References / ACR = Average Citations per Reference We introduced in 2010 - for the first time in scientific publishing, the term "References Weight", as a quantitative indication of the quality ... Read more Citations for references updated on 2024-10-02 08:34 in 198 seconds. Note1: Web of Science® is a registered trademark of Clarivate Analytics. Note2: SCOPUS® is a registered trademark of Elsevier B.V. Disclaimer: All queries to the respective databases were made by using the DOI record of every reference (where available). Due to technical problems beyond our control, the information is not always accurate. Please use the CrossRef link to visit the respective publisher site. |
Faculty of Electrical Engineering and Computer Science
Stefan cel Mare University of Suceava, Romania
All rights reserved: Advances in Electrical and Computer Engineering is a registered trademark of the Stefan cel Mare University of Suceava. No part of this publication may be reproduced, stored in a retrieval system, photocopied, recorded or archived, without the written permission from the Editor. When authors submit their papers for publication, they agree that the copyright for their article be transferred to the Faculty of Electrical Engineering and Computer Science, Stefan cel Mare University of Suceava, Romania, if and only if the articles are accepted for publication. The copyright covers the exclusive rights to reproduce and distribute the article, including reprints and translations.
Permission for other use: The copyright owner's consent does not extend to copying for general distribution, for promotion, for creating new works, or for resale. Specific written permission must be obtained from the Editor for such copying. Direct linking to files hosted on this website is strictly prohibited.
Disclaimer: Whilst every effort is made by the publishers and editorial board to see that no inaccurate or misleading data, opinions or statements appear in this journal, they wish to make it clear that all information and opinions formulated in the articles, as well as linguistic accuracy, are the sole responsibility of the author.