267 results found.
Year: 2017, Volume: 17, Number: 3
... capable of recognizing and are other studies on automatic power quality disturbance reporting power quality faults effectively within the real-time classification systems employing digital signal processor requirements. (DSP ... a quality detection to vibration sensing. NORMAL situation), the classification result (fault type), The FPGA configuration is designed using Xilinx ISE time and raw ...
Terms matched: 2 - Score: 13 - 1,622k
Year: 2017, Volume: 17, Number: 3
... many fields such as target tracking [1 ], networked control as zero-sum game and a minimax algorithm is developed to systems [2 ], process monitoring and fault detection [3 ], filter estimate target position in sensor networks. In [21], an design, and signal processing [4]. State ...
Terms matched: 1 - Score: 7 - 1,549k
Year: 2017, Volume: 17, Number: 2
... each note signal S(t ), firstly, the input parameters are are source independent [31]. In the proposed algorithm, in set to some defaults. Then, the basic atoms are extracted addition to the note-specific atoms that are instrument using this parameter set and the note-specific atom is dependent, the primary ...
Terms matched: 1 - Score: 3 - 1,709k
Year: 2017, Volume: 17, Number: 2
... on Industrial Informatics, vol. 5-1, pp. 22 – 37, on faulty multicore environments," Real-Time Systems, vol. 53, issue. 2009 ... invoke a FT, the following work [8] C. Krishna, "Fault-tolerant scheduling in homogeneous real-time [32] extended it to be applicable more general ...
Terms matched: 2 - Score: 5 - 1,218k
Year: 2017, Volume: 17, Number: 2
... and often involve problems like non-uniformity in intensity or one yield layer. LBR uses lazy learning method to ignore the biasness due to the magnetic field disparity or a fault in the small disjoint problem by constructing a rule for each test coils of the used system. Non-uniformity correction is using unique method. performed using bias field ...
Terms matched: 1 - Score: 3 - 1,628k
Year: 2017, Volume: 17, Number: 2
... value range [a, b] of the golden section search method is shown in Fig. 3. Figure 3. Golden section method In Gold-SA, initial default values for a and b are considered to be -π and π, respectively. These two coefficients are applied to the current and target values in the first ...
Terms matched: 1 - Score: 3 - 1,375k
Year: 2017, Volume: 17, Number: 2
... system does not have a The system is therefore limited in scalability and is direct interface and information transfer between nodes or a vulnerable to malfunction when the central controller faults. central control system, the only measurements available to This research proposes an additional degree of autonomy the node are local. The estimation system of a node ...
Terms matched: 1 - Score: 3 - 1,453k
Year: 2017, Volume: 17, Number: 2
... "Model-free 10.1109/TPEL.2014.2353215 predictive current control for interior permanent-magnet synchronous [16] G.F.H. Beng, X. Zhang, and D.M. Vilathgamuwa, "Sensor Fault- motor drives based on current difference detection technique," IEEE Resilient Control of Interior Permanent-Magnet Synchronous Motor Transactions on Industrial Electronics, vol. 61, no ...
Terms matched: 1 - Score: 3 - 2,573k
Year: 2017, Volume: 17, Number: 2
... 1, and chooses other points C. Emergency Access to define the polynomial q R. The points in the polynomial The emergency situation is handled by adding a default are made up of two types of nodes, level nodes and group policy as shown in Fig.4. randomly selected nodes from the access tree. It sets ...
Terms matched: 1 - Score: 3 - 1,311k
Year: 2017, Volume: 17, Number: 2
... Afterwards, the system reaction was monitored to detect and catch first fault. The faults were indicated by the blinking LED and buzzer from the EM, which recognized ... Advances in Electrical and Computer Engineering Volume 17, Number 2, 2017 Fault Detection Variants of the CloudBus Protocol for IoT Distributed Embedded Systems Alexander BARKALOV1, Larysa ...
Terms matched: 2 - Score: 72 - 1,934k