221 results found.
Year: 2016, Volume: 16, Number: 3
... disturbing its such as better power supply rejection ratio, greater dynamic quality factor. Functionality of the proposed filter in both S-E range of the processed signals, lower harmonic distortion and F-D form has been verified by PSpice simulations using and greater attenuation of common-mode signal. F-D available models of used active elements and also by circuits ...
Terms matched: 1 - Score: 3 - 1,290k
Year: 2009, Volume: 9, Issue: 2
... amplitude. It can be observed that in the T2= sin δ 3V2 proposed drive, there is a significant reduction in torque and flux ripples. Hence the harmonic distortion can also reduce. Hence: This can be observed from Fig. 6-a for the locus of stator T0= T7= 0.5(Ts T1 T2 ...
Terms matched: 1 - Score: 3 - 724k
Year: 2019, Volume: 19, Number: 2
... , Therefore, it is possible to analyze several cases in m is the number of GRID type elements in Circuit 2 and G#i distribution systems such as harmonics analysis and is the G-th element of the GRID type of Circuit# counting sequential time simulations called quasi-static solutions. the recloser on the output of the circuit ...
Terms matched: 1 - Score: 3 - 1,192k
Year: 2016, Volume: 16, Number: 2
... i qm  i q  iQ. (14), (15) machine; the stator windings are three-phase, symmetrical and sinusoidally distributed, without space harmonics; the The two magnetization curves are identical in case of field coil is placed in the longitudinal axis; supplementary cylindrical rotor SGs and they are different in ...
Terms matched: 1 - Score: 3 - 1,401k
Year: 2009, Volume: 9, Issue: 3
... rotor is another Figure 2. Electro-mechanical Battery under design. important parameter. Surface mounted permanent magnet machines are suitable because of higher energy density and TABLE I lower harmonic production [17]. The final important UNDER DESIGN EMB PARAMETERS parameter to select a proper structure is the pole numbers. Output Charge/discharge Min Max ...
Terms matched: 1 - Score: 3 - 552k
Year: 2021, Volume: 21, Number: 2
... [25]. In this analysis, these losses are initially estimated from the copper losses, the hysteresis, and the eddy current losses using the two-dimensional time harmonic finite element program using Matlab software. From the FEM analysis, the vector potential Az and the induced eddy current density in the rotor slots can be obtained ...
Terms matched: 1 - Score: 3 - 2,207k
Year: 2015, Volume: 15, Number: 3
... F1 score variation with the increase of the codebook size The recall and precision can be combined within a unique evaluation metric, denoted by F1 score defined as the harmonic mean of precision and recall rates: 2 P R F1score ; (8) PR Ideally, the precision, recall and F1 score should be equal ...
Terms matched: 1 - Score: 3 - 1,667k
Year: 2015, Volume: 15, Number: 3
... V. Maier, S. G. Pavel, C. D. Maier, I. Birou, "Correct Application of REFERENCES the Discrete Fourier Transform in Harmonics," Advances in Electrical [1] A. C. Gjerris, J. Staer-Jensen, J. S. Jorgensen, T. Bergholt, C ...
Terms matched: 1 - Score: 3 - 1,227k
Year: 2019, Volume: 19, Number: 4
... ï€ Lsh  (4) 2 where, Ll is the phase leakage inductance, Lav is the average component of self-inductance and Lsh is the magnitude of second harmonic component. The power factor (p.f) of SynRel is also affected by the (b) values of Ld and Lq and is presented in (5 ...
Terms matched: 1 - Score: 3 - 1,079k
Year: 2015, Volume: 15, Number: 3
... between the damped response at the transducer's The spectral analysis of the I1' (t) current reveals 2 terminals obtained through Spice simulation and the experimental setup, harmonics: one represented by the coil's frequency of during the coil's damping regime resonance, ω 1, the other by the vibrating wire's frequency of In the next ...
Terms matched: 1 - Score: 3 - 1,220k