379 results found.
Year: 2017, Volume: 17, Number: 4
... are phase control drives with thyristors or TRIACs. When the two boost inductors, Q 1 D 1 to Q 4 D 4 are four frequency exceeds 20kHz, noise is eliminated, filters are unidirectional switches with FETs and diodes. The converter smaller and efficiency is higher. The current waveform is much load contains the R ...
Terms matched: 1 - Score: 3 - 1,545k
Year: 2018, Volume: 18, Number: 1
... proposed method uses signals are obtained for both the time and frequency domain. In the from three accelerometer sensor axes of a smartphone. signal pre-processing step, the noise on the signal is Signal processing techniques are used to extract the features removed. The first three feature signals are the RMS values of the obtained signals. ...
Terms matched: 1 - Score: 3 - 1,367k
Year: 2017, Volume: 17, Number: 2
... the whole system is optimized to require only electromagnetic waves generated by other electronic few resources. The microcontroller is used from the devices; in most cases, the noise from the electrical low-power family, so the total current consumption will network and the harmonics of this disturbing signal are be approx. 43mA (having activated the ...
Terms matched: 1 - Score: 3 - 2,915k
Year: 2018, Volume: 18, Number: 1
... . doi:10.1142/S0218001415550083. [12] T. Mallick, P. P. Das, and A. K. Majumdar, "Characterizations of Noise in Kinect Depth Images: A Review," IEEE Sensors Journal, vol. 14, no. 6, pp. 1731 – 1740, Jun. ...
Terms matched: 1 - Score: 3 - 1,058k
Year: 2017, Volume: 17, Number: 2
... obtain and III. The single note signals in RWC are recorded at optimum parameters, the execution time is comparable. laboratory. So, there is not any noise or background signals in the test samples which are made by summation of single VI. CONCLUSION note signals and consequently, separation process for those In this paper ...
Terms matched: 1 - Score: 3 - 1,709k
Year: 2017, Volume: 17, Number: 1
... [29] N. Celebi, "An accurate single CAD model based on radial basis [8] M. Yucel, Z. Aslan, "The noise figure and gain improvement of function network", Optoelectron. Adv. Mater. – Rapid Commun., vol. double-pass C- band EDFA", ...
Terms matched: 1 - Score: 3 - 1,216k
Year: 2016, Volume: 16, Number: 3
... operating practically implemented by a universal current conveyor in the current-mode are that these circuits can provide (UCC) [25] which was developed at Brno University greater signal-to-noise ratio and dynamic range, lower of Technology. Implementation of the MO-CF using the power consumption and wider frequency bandwidth UCC is shown in Fig. 1. ...
Terms matched: 1 - Score: 3 - 1,290k
Year: 2016, Volume: 16, Number: 4
... . Mitsantisuk, "FPGA- rendered by the practical implementation of a custom Based High-Performance Force Control System With Friction-Free interrupt management scheduler, based on the nMPRA and Noise-Free Force Observation," IEEE Trans. Ind. Electron., vol. architecture. Tests conducted and presented in section III 61, no. 2, ...
Terms matched: 1 - Score: 3 - 1,395k
Year: 2018, Volume: 18, Number: 2
... extracts the most relevant ones for the years old. The recordings are taken in a soundproofed room classification. Mel-frequency cepstral coefficients (MFCC) to minimize the background noise. They are recorded in 16 are used as inputs to the DNN. The compressed features are kHz, 16 bits, pulse code modulation (PCM) ...
Terms matched: 1 - Score: 3 - 1,145k
Year: 2018, Volume: 18, Number: 2
... transformation is realized by virtue of the obtained pixel values have been compared. For comparison purposes coefficients and the resultant image after the reconstruction PSNR (Peak Signal to Noise Ratio) [40] is frequently used process is given in the Fig. 14. criterion in compression performance. RMSE graphic is supplied in Figure 15 ...
Terms matched: 1 - Score: 3 - 1,609k