591 results found.
Year: 2015, Volume: 15, Number: 3
... 1 can be measured (R 1 =100Ω, L 1 =25mH, C 1 =280pF). The wire's parameters can be determined using the reflected load theory (R w =5Ω, L w =25mH, C w =1.8µF). Then, the equivalent circuit of the Figure 4. Input ...
Terms matched: 1 - Score: 6 - 1,220k
Year: 2015, Volume: 15, Number: 3
... middleware to attributes. The CTOAS will fabricate its own EC and then develop new technology for group communication and use it to make EULS. Finally, we apply overload technique resource sharing across heterogeneous embedded systems. of object-oriented theory to specify how EC works among This project presented service oriented architecture [14-15] CEO, CEOAS ...
Terms matched: 1 - Score: 6 - 1,291k
Year: 2015, Volume: 15, Number: 3
... ontological terms. II. DISCUSSION Dong-mei et al. [7] describes an ontology based automatic Data products from satellite observations are used for extract, transform and load (ETL) method for Ocean data various purposes in different applications such as natural integration. The approach has four phases 1) extract data resource management, ...
Terms matched: 1 - Score: 6 - 1,152k
Year: 2010, Volume: 10, Issue: 2
... method of low power industrial applications. In practice, where real estimation. data are used, the driver parameters and the system parameters are unknown or varying with load conditions. In II. DESCRIPTION OF THE METHOD this paper, the dynamic treatment of Servo Motor with its driver is considered as the system that must be ...
Terms matched: 1 - Score: 6 - 1,664k
Year: 2009, Volume: 9, Issue: 3
... simulations are Figure 1 shows a block diagram of a LEO satellite used to achieve this aim. Ansoft Maxwell-2D software is electrical subsystem using EMB. Solar cells supply loads used for FEM simulations. and also charge EMB during the day. EMB supply the loads Particle Swarm Optimization (PSO) will be used for the during ...
Terms matched: 1 - Score: 6 - 552k
Year: 2009, Volume: 9, Issue: 1
... can reach maximum speeds between 2.5-8 m/s, The main results are given in table I, separately on the depending on the road gradient – at a load of 80kg, and 20- two variants of the reluctance motors. Other geometric 30% higher speeds – at a load of 60kg, as shown in ...
Terms matched: 1 - Score: 6 - 884k
Year: 2016, Volume: 16, Number: 2
... . In this paper we will usability of the system, unfortunately they often neglect this demonstrate how to build a classifier that exploits these asymmetry in the user's cognitive load. This, along with the variations and allows the adversary to successfully perform fact that the users respond to given challenges immediately the timing attack on high-complexity CAS ...
Terms matched: 1 - Score: 6 - 1,341k
Year: 2023, Volume: 23, Number: 3
... mean the best one [23]. Other factors calculation of the equivalent-density does not generate an must be considered in order to improve route quality. From extra overload, because counting is performed with routing this point of view, IC_AOMDV uses a new route metric, messages that already exist in the classic protocol. which ...
Terms matched: 1 - Score: 6 - 1,374k
Year: 2008, Volume: 8, Issue: 2
... in the practical fault analysis standards (such as known. If they are not known, they could be calculated from IEC, IEEE, etc.). load losses. For two-winding transformers, one could Calculation of fault currents due to a winding fault of a assume that per unit values of primary and secondary power ...
Terms matched: 1 - Score: 6 - 733k
Year: 2019, Volume: 19, Number: 2
... , switching frequency, and [6] A. Ayed, Tr. Dubois, J. L. Levant, and G. Duchamp, "A New method load capacitance. This dependency is clearly depicted by the for the characterization of electronic components immunity," IEEE measurement results in Fig. 19. Note that the ...
Terms matched: 1 - Score: 5 - 1,450k