569 results found.
Year: 2009, Volume: 9, Issue: 3
... with Near Sinusoidal kinetic energy associated with the inertias of the motor and Input Currents), as show in Figure 3 [7 – 9]. When the load is recovered and fed back into the utility system [1 – 3]. energy is transferred from the DC side to the AC side, the Usually ...
Terms matched: 1 - Score: 13 - 317k
Year: 2015, Volume: 15, Number: 3
... 300.01 The fault resistance (R f) can modify significantly the calculated distance to the fault in conventional relays [21]. E. Case V: Different load and operating conditions In order to evaluate the impact of this parameter in the algorithm performance, several cases were analyzed as The algorithm performance was analyzed with different ...
Terms matched: 1 - Score: 13 - 1,306k
Year: 2014, Volume: 14, Number: 1
... calculation, according to power squirrel cage motors are continuously reevaluated and the design method. enriched with new elements. The final goal is to optimize the performances for load C. Determining the minimum of the objective function operation [2 ], [17-18], by increasing the estimation accuracy To optimize the multivariable problems, ...
Terms matched: 1 - Score: 13 - 1,120k
Year: 2009, Volume: 9, Issue: 3
... study of the discussed controllers is made both in transient and steady states. Once the membership degree is determined, an inference is We have analyzed the effect of load variation and of carried out in line, in order to obtain accurate results. rotation sense inversion under the choice of the reference Knowledge reflecting the actions of ...
Terms matched: 1 - Score: 13 - 290k
Year: 2010, Volume: 10, Issue: 3
... variation a maximum power is achieved only if the system working point is brought near the maximum power point (MPP). The proposed system, making transferred toward load or storage device [5-9]. use of several MPPT control algorithms (Perturb and Observe, Incremental conductance, Fuzzy Logic), demonstrates in II. ...
Terms matched: 1 - Score: 12 - 1,333k
Year: 2008, Volume: 8, Issue: 1
... sliding mode control and sliding mode control. The feedback control algorithms were iterated until best. simulation results were obtained.. The simulation of the starting mode without load is done,. followed by speed reference ωre= 150 rd/ s to Rule (i): if s Fsi, then u is Fui ωre ...
Terms matched: 1 - Score: 11 - 434k
Year: 2021, Volume: 21, Number: 3
... : ESXi and Xen. for any possible use case, but the behavior of a hypervisor 4. The differences related to the sections related to depends on the workload characteristics. It is clear that mathematical modeling and expected behavior paper [1] has significantly richer future work, but the main In [1 ], ...
Terms matched: 1 - Score: 11 - 938k
Year: 2015, Volume: 15, Number: 2
... , while the second step is carried out (http://www-graphics.stanford.edu/data/3Dscanrep/) and the on the CPU. To evaluate the computational workload and GIT Large Geometry Models Archive performance bottleneck of the CudaPre3D, we record the (http://www.cc.gatech. edu/projects/large_models/) ...
Terms matched: 1 - Score: 11 - 1,019k
Year: 2007, Volume: 7, Issue: 2
... stores data on this controller and can Peripheral Interface), 40 MHz maximum speed. The command it to send data to the application running on the microcontroller is loaded with a C written program and it remote computer. has the following tasks: read packets through SPI from The motor used for this project is a direct ...
Terms matched: 1 - Score: 11 - 468k
Year: 2020, Volume: 20, Number: 2
... 15] using extra hardware and memory storage for real-time phase inductance coordinate transformations. This method is implementation. Complete sensorless control of a three-phase not appropriate for high load and high speed driving – 6/4-pole switched reluctance motor drive system is carried out running conditions. using Matlab/Simulink. Also, it is implemented ...
Terms matched: 1 - Score: 11 - 1,647k